[Mar-2025] Get 100% Real 300-410 Exam Questions, Accurate & Verified NewPassLeader Dumps in the Real Exam!
Pass Your CCNP Enterprise Exams Fast. All Top 300-410 Exam Questions Are Covered.
Prerequisites for Cisco 300-410 Exam
This certification exam does not have any official prerequisites. However, the students are required to possess the knowledge of the topics presented in its content before taking the test. This is the only way to get the required passing score. Besides that, it is recommended that the candidates have an understanding of network fundamentals and possess the relevant skills in implementing LANs as well as managing & securing network devices.
NEW QUESTION # 296
Refer to the exhibit.
Why is user authentication being rejected?
- A. The TACACS+ server is down, and the user is in the local database.
- B. The TACACS+ server is down, and the user is not in the local database.
- C. The TACACS+ server expects "user", but the NT client sends "domain/user".
- D. The TACACS+ server refuses the user because the user is set up for CHAP.
Answer: B
NEW QUESTION # 297
Refer to the exhibit. A network engineer receives a fault ticket about traffic drops from BANK SITE to BANK Users can reach BANK SITE Y from router RA as a source.
Routers RB and RD are acting as route reflectors.
Which configuration resolves the issue?
- A. RC(config)#router bgp 65201
RC(config-router)#neighbor 10.10.10.4 route-reflector-client - B. RB(config)router bgp 65201
RB(config-router)#neighbor 10.10.10.3 route-reflector-client - C. RC(config)#router bgp 65201
RC(config-router)#neighbor 10.10.10.2 route-reflector-client - D. RF(config)#router bgp 65201
RF(config-router)#neighbor 10.10.10.6 route-reflector-client
Answer: A
NEW QUESTION # 298
Refer to the exhibit.
Which two actions restrict access to router R1 by SSH? (Choose two.)
- A. Configure transport input ssh on line vty and remove sequence 30 from access list 100.
- B. Configure transport output ssh on line vty and remove sequence 10 from access list 199.
- C. Configure transport output ssh on line vty and remove sequence 20 from access list 100.
- D. Remove sequence 10 from access list 100 and add sequence 20 deny tcp any any eq telnet to access list
199 - E. Remove class-map ANY from service-policy CoPP
Answer: A,C
NEW QUESTION # 299
Refer to the exhibit.
An engineer cannot copy the IOS.bin
Which action resolves the issue?
- A. Use the copy flash:/ ftp://[email protected]/IOS.bin command.
- B. Make memory space on the switch flash or USB drive to download the file.
- C. Add the IOS.bin file, which does not exist on FTP server.
- D. Allow file permissions to download the file from the FTP server.
Answer: C
NEW QUESTION # 300
Refer to the exhibit.
An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting. Which command must be used in configuration mode to enable SSH on the device?
- A. ip ssh version 2
- B. no ip ssh disable
- C. crypto key generate rsa
- D. ip ssh enable
Answer: C
NEW QUESTION # 301
The network administrator is tasked to configure R1 to authenticate telnet connections based on Cisco ISE using RADIUS. ISE has been configured with an IP address of 192.168.1.5 and with a network device pointing towards R1 (192.168.1.1) with a shared secret password of Cisco123. If ISE is down, the administrator should be able to connect using the local database with a username and password combination of admin/cisco123.
The administrator has configured the following on R1:
ISE has gone down. The Network Administrator is not able to Telnet to R1 when ISE went down. Which two configuration changes will fix the issue? (Choose two.)
- A. Option A
- B. Option D
- C. Option C
- D. Option E
- E. Option B
Answer: C,D
NEW QUESTION # 302
Refer to Exhibit.
The network administrator configured the branch router for IPv6 on the E0/0 interface. The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?
- A. Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command
- B. Enable the IPv4 address family under the E0/0 interface by using the address-family ipv4 unicast command
- C. Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E0/0 interface
- D. Disable IPv6 on the E0/0 interface using the no ipv6 enable command
Answer: A
Explanation:
Explanation
Once again, Cisco changed the IOS configuration commands required for OSPFv3 configuration. The new OSPFv3 configuration uses the "ospfv3" keyword instead of the earlier "ipv6 router ospf" routing process command and "ipv6 ospf" interface commands.
The Open Shortest Path First version 3 (OSPFv3) address families feature enables both IPv4 and IPv6 unicast traffic to be supported. With this feature, users may have two processes per interface, but only one process per address family (AF).
NEW QUESTION # 303
Refer to the exhibit.
A network engineer receives a fault ticket about traffic drops from BANK SITE to BANK Users can reach BANK SITE Y from router RA as a source.
Routers RB and RD are acting as route reflectors.
Which configuration resolves the issue?
- A. RC(config)#router bgp 65201
RC(config-router)#neighbor 10.10.10.4 route-reflector-client - B. RB(config)router bgp 65201
RB(config-router)#neighbor 10.10.10.3 route-reflector-client - C. RC(config)#router bgp 65201
RC(config-router)#neighbor 10.10.10.2 route-reflector-client - D. RF(config)#router bgp 65201
RF(config-router)#neighbor 10.10.10.6 route-reflector-client
Answer: A
NEW QUESTION # 304
What does the PE router convert the Ipv4 prefix to within an MPLS VPN?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: A
NEW QUESTION # 305
Refer to the exhibit.
Redistribution is enabled between the routing protocols, and nowPC2 PC3, and PC4 cannot reach PC1. What are the two solutions to fix the problem? (Choose two.)
- A. Filter RIP AND OSPF routes back into OSPF from EIGRP when redistributing into OSPF in R2
- B. Filter OSPF routes into RIP FROM EIGRP when redistributing into RIP in R2.
- C. Filter all routes except EIGRP routes when redistributing into OSPF in R3.
- D. Filter RIP routes back into RIP when redistributing into RIP in R2
- E. Filter all routes except RIP routes when redistributing into EIGRP in R2.
Answer: D,E
Explanation:
Even PC2 cannot reach PC1 so there is something wrong with RIP redistribution in R2. Because RIP has higher Administrative Distance (AD) value than OSPF and EIGRP so it will be looped when doing mutual redistribution.
NEW QUESTION # 306 
Refer to the exhibit An engineer configured NetFlow but cannot receive the flows from R1 Which two configurations resolve the issue? (Choose two )
- A.
- B.
- C.
- D.
- E.
Answer: C,E
NEW QUESTION # 307
Clients on ALS2 receive IPv4 and IPv6 addresses but clients on ALS1 receive only IPv4 addresses and not IPv6 addresses. Which action on DSW1 allows clients on ALS1 to receive IPv6 addresses?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: A
Explanation:
Explanation
https://community.cisco.com/t5/networking-documents/stateful-dhcpv6-relay-configuration-example/ta-p/31493
NEW QUESTION # 308
Refer to the exhibit.
A user cannot SSH to the router. What action must be taken to resolve this issue?
- A. Configure transport output ssh
- B. Configure ip ssh source-interface loopback0
- C. Configure ip ssh version 2
- D. Configure transport input ssh
Answer: D
Explanation:
Explanation
https://www.cisco.
com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/security/configuration_guide/b_sec_15
NEW QUESTION # 309
Refer to the exhibit. Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day.
Which action fixes the issue within the current resources?
- A. Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool
- B. Configure the DHCP lease time to a smaller value
- C. Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool
- D. Configure the DHCP lease time to a bigger value
Answer: B
Explanation:
Section: Infrastructure Services
Explanation
NEW QUESTION # 310
Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?
- A. Router(config-router)#ospfv3 3 1
- B. Router(config-router)#ospfv3 1 ipv4 area 0
- C. Router# ospf3 1 address-family ipv4
- D. Router# ospfv3 1 address-family ipv4 unicast
Answer: B
Explanation:
The newest OSPFv3 configuration approach utilizes a single OSPFv3 process. It is capable of supporting IPv4 and IPv6 within a single OSPFv3 process. OSPFv3 builds a single database with LSAs that carry IPv4 and IPv6 information. The OSPF adjacencies are established separately for each address family. Settings that are specific to an address family (IPv4/IPv6) are configured inside that address family router configuration mode.
Running single OSPFv3 for both IPv4 and IPv6 is supported since Cisco IOS Software Release
15.1(3)S.
The new-style OSPFv3 process is enabled using the router ospfv3 process-number command.
Within the OSPF process configuration mode, the OSPF process ID is defined (using the router- id ospf-process-ID command).
OSPFv3 New-Style OSPF Configuration Commands:
Therefore answer B is the best answer here but in this answer, the configuration mode is not correct. It should be interface mode (config-if)#, not router mode (config-router)#.
Reference: https://www.ciscopress.com/articles/article.asp?p=2294214&seqNum=4
NEW QUESTION # 311
Refer to the Exhibit. The access-lists are configured on the network device. There is a server behind the network device. User are trying to access the server securely however they are not able to access it. What changes would you recommend to the above configuration?
- A. Permit tcp any any
- B. Permit tcp port 443
- C. Permit tcp port 465
- D. Permit tcp port 3389
Answer: B
NEW QUESTION # 312
After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for several service provides. Which configuration ensures that the branch router in AS 45123 advertises only the local networks to all SP neighbors?
A)
B)
C)
D)
- A. Option A
- B. Option C
- C. Option D
- D. Option B
Answer: C
Explanation:
By default BGP advertises all prefixes to external BGP neighbors. This means that if you are multi-homed (connected to two or more ISPs) then you might become a transit AS. For example, ISP 2 in AS 200 can send traffic to your router in AS 100 to reach ISP 3 in AS 300 because you advertised prefixes in ISP 3 to ISP 2.
This is what will be seen in the BGP routing table of ISP1:
NEW QUESTION # 313
Refer to the exhibit.
Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?
- A. Option A
- B. Option C
- C. Option D
- D. Option B
Answer: A
NEW QUESTION # 314 
Refer to the exhibit. The company implemented uRPF to address an antispoofing attack. A network engineer received a call from the IT security department that the regional data center is under an IP attack Which configuration must be implemented on R1 to resolve this issue?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: A
NEW QUESTION # 315
Drag and drop the actions from the left into the correct order on the right to configure a policy to avoid following packet forwarding based on the normal routing path.
Answer:
Explanation:
NEW QUESTION # 316 
Refer to the exhibit Which command must be configured to make VRF CCNP work?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: A
NEW QUESTION # 317
A company is expanding business by opening 35 branches over the Internet. A network engineer must configure DMVPN at the branch routers to connect with the hub router and allow NHRP to add spoke routers securely to the multicast NHRP mappings automatically Which configuration meets this requirement at the hub router?
A)
B)
C)
D)
- A. Option A
- B. Option D
- C. Option C
- D. Option B
Answer: C
Explanation:
The command "ip nhrp map multicast dynamic" allows NHRP to automatically add spoke routers to the multicast NHRP mappings.
NEW QUESTION # 318
Refer to the exhibit.
A network administrator sets up an OSPF routing protocol for a DMVPN network on the hub router. Which configuration required to establish a DMVPN tunnel with multiple spokes?
- A. ip ospf network point-to-point on both spoke routers
- B. ip ospf network point-to-point on the hub router
- C. ip ospf network point-to-multipoint on both spoke routers
- D. ip ospf network point-to-multipoint on One spoke router
Answer: C
NEW QUESTION # 319
......
Penetration testers simulate 300-410 exam: https://itcert-online.newpassleader.com/Cisco/300-410-exam-preparation-materials.html